• metric
  • electrical takeoff
  • estimating

How do you do an electrical takeoff in metric?

Read the 1:100 or 1:50 scale off the title block, check it against the paper size, measure in metres and m², and price cable and conduit per metre.

The TakeOn Team 6 min read

A fragment of an electrical floor plan with count markers on devices and a measured run between them totalling 26.21 m

In short: An electrical takeoff in metric works the same way as one in feet: set the scale on each sheet, count the devices, measure the runs and price the quantities. The differences are the scale and the units. Metric drawings state a ratio such as 1:100 or 1:50, and that ratio is only true on the paper size it was drawn for. Lengths come out in metres, areas in m², and cable and conduit are priced per metre. In TakeOn you set the workspace to Metric and it does all of that, from the scale on the title block to the proposal.

Key takeaways

  • Read the scale off the title block, and check it against the paper size. A 1:100 @ A1 sheet printed on A3 measures at 1:200.
  • Measure in metres and m², and keep the whole estimate in metres. A price per metre times metres is the line total, with no conversion step to get wrong.
  • In TakeOn, Settings → Workspace → General → Units → Metric changes the drawing, the Takeoffs panel, the Bid Summary, exports, the report, the proposal and your AI assistant together.
  • TakeOn does the measuring and pricing in metric. It does not check work against BS 7671, AS/NZS 3000 or any other national wiring rules.

What is a metric electrical takeoff?

A metric electrical takeoff is a count and measurement of the electrical work on a set of drawings, done in metres and square metres instead of feet. You count fixtures, outlets, switches and panels, and measure cable, conduit, tray and trunking runs, in the units the drawings and your suppliers use. The result is a list of quantities you can price. If the takeoff itself is new to you, start with what an electrical takeoff is.

How do you read a metric scale like 1:100?

A metric scale of 1:100 means 1 unit on the paper is 100 of the same unit on site: 10 mm on the drawing is 1,000 mm, or 1 m, on the building. Floor plans are usually 1:100 or 1:50, enlarged plans and plant rooms 1:20 or 1:50, and site plans 1:200 to 1:500.

TakeOn reads these ratios from the title block. A sheet that says 1:100 or SCALE 1:50 is scaled when the plans are processed, with no inches-to-feet conversion. Sheets it can’t read, or that you want to set by hand, take a custom 1 : N in Set Page Scale. Owners can add the 14 common metric scales (1:1 to 1:2500) as one-click presets with Add metric scales under Settings → Workspace → Scales.

Why does the paper size matter on a metric drawing?

The paper size matters because a ratio scale is only true at the size the sheet was drawn for. Metric title blocks often say so, for example 1:100 @ A1. Print or export that sheet at A3 and everything is half the size in each direction, so the copy you were sent is 1:200. Measure it at 1:100 and every run is half its real length.

TakeOn checks this for you. When a scale names a paper size, TakeOn compares it with the PDF’s actual page size. On the A1 PDF it reads 1:100. On an A3 copy of the same sheet it reads 1:200, labelled 1:200 (1:100 @ A1) so you can see why. A title block that lists both (1:100 @ A1 / 1:200 @ A3) takes the one that matches the page.

If a drawing has no usable scale, or you don’t trust it, use Measure a known distance in Set Page Scale. Type a dimension you can see on the sheet in metres or millimetres, click its two ends, and TakeOn works out the ratio from it.

How do you set up TakeOn to work in metric?

You set up TakeOn for metric with one setting on the workspace:

  1. Open Settings → Workspace → General.
  2. Set Units to Metric. Only the workspace owner can change it.
  3. Optional: set Date & number format to your country, such as English (UK), English (Australia), English (New Zealand) or English (Ireland), so dates read 16/11/2026 on screen and 16 November 2026 on PDFs.
  4. Optional: under Settings → Workspace → Scales, click Add metric scales.

A new workspace picks this up at sign-up. Choose a metric country such as the UK, Ireland, Australia or New Zealand and the workspace starts in metric, with the currency and date format for that country. Its starter templates and kits come in metric values chosen for metric work (kit lengths in metres and drops in metres), not feet values converted to awkward decimals. You can change the units on that setup step.

TakeOn has one unit system per workspace, not per project, so a team that bids both imperial and metric work would use a workspace for each.

Where do metres and m² show up in TakeOn?

On a metric workspace, TakeOn shows lengths in metres and areas in m² everywhere the quantities appear:

WhereWhat it shows
The drawingRun lengths and area labels while you measure, in m and m²
The Takeoffs panelEach template’s quantity and section subtotals in m and m²
The Bid SummaryMaterial and labor rows priced per metre and per m²
ExportsThe Excel and CSV takeoff with metric quantities and units
The report and proposalThe branded PDF report and the client proposal, in metres
Your AI assistantQuantities in m and m², read through the TakeOn MCP connector

Lengths you type can be in metres, centimetres or millimetres. 3, 3 m, 300 cm and 3000 mm all mean three metres. A bare number is read as metres.

How do you price cable and conduit per metre?

You price cable and conduit per metre by giving each material a price per metre and letting the measured metres multiply it. On a metric workspace the estimate runs in metres, so a cable priced in £/m (or €/m, A$/m, NZ$/m) times the metres you measured is the line total. There’s no hidden feet-to-metres step in the middle to get the price wrong by a factor of 3.28.

Labor works the same way: hours per metre of conduit, per m² of an area template, or per item for a count. Formulas such as a drop allowance or a service loop per run are written in metres too. If you price with assemblies, a run’s kit takes its measured length in metres and expands into the fittings and fixings it needs.

What happens when you switch an existing workspace to metric?

When an owner switches an existing TakeOn workspace from imperial to metric, TakeOn converts what was typed per foot so the estimate stays right:

  • Material prices and labor per foot become per metre.
  • Pack sizes and kit length inputs are converted.
  • Plain labor or cost numbers on linear and area templates are converted.
  • Formulas it can’t safely rewrite, like one that adds a fixed length to the measured run, are left as written and listed under Review units for you to check.

Locked bids keep the units they were locked in, so a bid you’ve already sent reads the same afterwards. Teammates’ edits pause for the few seconds the switch takes, and a banner tells them why.

What doesn’t TakeOn do in metric?

TakeOn measures, counts and prices in metric, but it doesn’t know your country’s wiring rules. To be plain about the limits:

  • No BS 7671, AS/NZS 3000 or AS/NZS 3008 checks. TakeOn doesn’t size cables, check volt drop or check containment fill against any national standard. You do that, as you would with any takeoff tool.
  • Two calculators are metric; the other code calculators are US code. The metric voltage drop calculator (mV/A/m) and the metric conduit fill calculator (mm) work from figures you type in from the datasheet or your wiring rules, with no built-in tables. The other code calculators at /tools/ and the code posts on this blog follow the US National Electrical Code (NEC), or NFPA 72 for the fire alarm battery calculator. The estimating and cable footage tools there, such as markup and margin, labor burden and bid capacity, follow no code.
  • Servers are in the US. TakeOn is hosted in US-East.
  • The app is in English. Dates and number formats follow your country; the screens themselves stay in English.

See TakeOn in metric for everything a metric workspace does, or try TakeOn free and pick your country when it asks, to start in metric.

Frequently asked questions

Does TakeOn work in metric?
Yes. A TakeOn workspace set to Metric (Settings → Workspace → General → Units) shows lengths in metres and areas in m² on the drawing, in the Takeoffs panel, the Bid Summary, exports, the PDF report and the proposal, and to your AI assistant. Material prices, labor, formulas and kit inputs are per metre too.
Can TakeOn read a 1:100 scale off a drawing?
Yes. TakeOn reads ratio scales such as 1:100 and SCALE 1:50 from the title block and scales the sheet automatically. A scale given with a paper size, like 1:100 @ A1, is checked against the PDF's real page size, so an A3 print of an A1 sheet is read as 1:200.
What happens to an A1 drawing printed on A3?
An A1 drawing printed on A3 is reduced by half in each direction, so a sheet marked 1:100 @ A1 measures at 1:200 on the A3 copy. Measuring it at 1:100 makes every length half what it should be. TakeOn compares the stated paper size with the PDF's page size and labels the A3 copy 1:200 (1:100 @ A1).
Can I switch an existing TakeOn workspace from feet to metres?
Yes. An owner changes Units in Settings → Workspace → General. TakeOn converts per-foot material prices, pack sizes, kit length inputs and plain labor or cost numbers to per metre, and lists formulas it can't safely convert under Review units. Locked bids keep the units they were locked in.
Does TakeOn check work against BS 7671 or AS/NZS 3000?
No. TakeOn measures and prices in metric, but it doesn't check designs or cable sizes against BS 7671, AS/NZS 3000, AS/NZS 3008 or any other national wiring rules. Its free metric voltage drop and conduit fill calculators work from figures you type in, with no built-in tables. Its other code calculators and code articles follow US codes: the National Electrical Code (NEC), and NFPA 72 for the fire alarm battery calculator. The estimating and cable footage tools, such as markup, labor burden and bid capacity, follow no code.