• estimating
  • electrical estimating

Why is 12 AWG wire rated 25 A but only on a 20 A breaker?

NEC Table 310.16 lists 12 AWG copper at 25 A (75 °C), but 240.4(D)(5) caps its breaker at 20 A. The higher ampacity is for derating, not a bigger breaker.

The TakeOn Team 5 min read

A calculator card with labelled inputs for load, material, insulation and length, and a blank result

In short: 12 AWG copper is listed at 25 A in the 75 °C column of NEC Table 310.16 (and 30 A at 90 °C), but NEC 240.4(D)(5) separately limits its overcurrent protection to 20 A. The table tells you how much current the wire can carry; 240.4(D) tells you the largest breaker or fuse allowed on it, and for 14, 12 and 10 AWG the breaker limit is the lower number. The higher ampacities still matter: they are where derating starts.

Key takeaways

  • Table 310.16 gives 12 AWG copper 20 / 25 / 30 A in the 60 / 75 / 90 °C columns. 240.4(D)(5) caps its breaker at 20 A.
  • The same rule caps 14 AWG copper at 15 A and 10 AWG copper at 30 A; 12 AWG aluminum at 15 A and 10 AWG aluminum at 25 A.
  • The higher table values are the starting point for ambient and conductor-count derating, which is why a derated 12 AWG can often stay on a 20 A breaker.
  • 240.4(G) exempts specific applications, motor circuits among them, which follow their own articles.

All code references here are to the 2023 NEC, the edition our wire ampacity calculator uses.

What is the ampacity of 12 AWG wire?

The ampacity of 12 AWG copper in NEC Table 310.16 is 20 A at 60 °C, 25 A at 75 °C and 30 A at 90 °C. Those values assume no more than three current-carrying conductors in the raceway or cable and an ambient of 30 °C (86 °F). Which column you can use depends on the conductor’s insulation and on the temperature rating of the terminations it lands on (110.14(C)): the conductor can’t be loaded past the column of its lowest-rated termination.

A worked example, from the wire ampacity calculator’s starting values: 12 AWG copper THHN (90 °C) on 75 °C terminations, at 86 °F, three current-carrying conductors.

StepResultSource
Base ampacity, 90 °C column30 ATable 310.16
Ambient and conductor-count factors× 1.00 × 1.00Tables 310.15(B)(1)(1), 310.15(C)(1)
Termination limit, 75 °C column25 ATable 310.16, 110.14(C)
Allowable ampacity25 Athe lower of the two
Largest breaker20 A240.4(D)(5)

The wire is good for 25 A. The breaker is still 20 A.

Why is 12 AWG limited to a 20 A breaker?

12 AWG copper is limited to a 20 A breaker because NEC 240.4(D) sets a fixed maximum overcurrent protection for small conductors, separate from their ampacity. Unless 240.4(E) or (G) permits more, the protection can’t exceed these values, after any correction factors for ambient temperature and number of conductors have been applied:

ConductorMax overcurrent protectionSection
14 AWG copper15 A240.4(D)(3)
12 AWG aluminum or copper-clad aluminum15 A240.4(D)(4)
12 AWG copper20 A240.4(D)(5)
10 AWG aluminum or copper-clad aluminum25 A240.4(D)(6)
10 AWG copper30 A240.4(D)(7)

Each of these is below the conductor’s 75 °C ampacity: 14 AWG copper is listed at 20 A, 12 AWG copper at 25 A and 10 AWG copper at 35 A; 12 AWG aluminum at 20 A and 10 AWG aluminum at 30 A. So for 14 through 10 AWG, the breaker limit, not the table, usually decides the breaker. The rule doesn’t give a reason; what it means in practice is that the higher columns for these sizes are for derating, not for a bigger breaker. (The 2026 NEC adds 10 A branch circuits on smaller conductors. If your jurisdiction has adopted 2026, check that edition’s text.)

So what is the 30 A rating for?

The 30 A, 90 °C rating of 12 AWG THHN is the number you derate from. When more than three current-carrying conductors share a raceway, or the ambient is hot, 310.15 reduces the ampacity, and starting from the higher column leaves more room before the wire drops below 20 A.

A worked example from the same calculator: six current-carrying 12 AWG copper conductors in one raceway take an adjustment factor of 0.80.

  • From the 90 °C column (THHN): 30 A × 0.80 = 24 A. That is still at least 20 A, so the circuit stays on a 20 A breaker.
  • From the 75 °C column: 25 A × 0.80 = 20 A, with no margin left.

When and how you may use the 90 °C column is its own question, covered in can you use the 90 °C column for THHN wire.

Does the 20 A limit change what size wire you need?

Yes. For a small load, 240.4(D) often sets the wire size, not ampacity. The wire size calculator runs both checks separately. In its example, a 20 A non-continuous load on copper with 90 °C insulation and 75 °C terminations:

  1. Ampacity needs only 14 AWG, which is listed at 20 A in the 75 °C column.
  2. 240.4(D) needs 12 AWG, because 14 AWG copper can’t be on more than 15 A.
  3. Voltage drop, with the example’s 100 ft one-way run at 120 V single-phase and a 3% target, calls for 8 AWG.

The calculator’s answer is the largest of the three: 8 AWG, set by voltage drop. The 3% target is a recommendation, not a code requirement: it comes from an informational note to 210.19(A), and informational notes aren’t enforceable (90.5(C)), though a specification, an energy code or the authority having jurisdiction may make it one. The code minimum here is 12 AWG, set by 240.4(D). Branch-circuit wire on a bid is rarely sized by ampacity alone, which is why the run length on the takeoff matters as much as the load.

When can 12 AWG be on a breaker larger than 20 A?

12 AWG can be on a breaker larger than 20 A only where 240.4(E) or 240.4(G) permits it. 240.4(E) covers tap conductors. 240.4(G) lists specific applications whose conductors are protected under their own articles instead, including:

  • Motor and motor-control circuit conductors, under Article 430.
  • Air-conditioning and refrigeration equipment circuit conductors, under Article 440.

That is why an air-conditioner nameplate can call for a maximum breaker larger than 240.4(D) would allow on its wire size. Motor circuits get their own post: why a motor’s breaker can be bigger than its wire. For a general-purpose branch circuit, the 20 A limit stands.

How do you check your own circuit?

You check your own circuit by running its conductor through the wire ampacity calculator, which shows the derating and the 240.4(D) limit side by side, or by starting from the load with the wire size calculator. For the run-length side, the voltage drop calculator checks a size against its run. TakeOn measures those run lengths off the PDF plans, so the number you check is the one you bid.

Try TakeOn free to measure your runs and counts from the plans.

Frequently asked questions

Can you put 12 AWG copper wire on a 25 A breaker?
Not as a general rule. NEC 2023 section 240.4(D)(5) limits the overcurrent protection for 12 AWG copper to 20 A, even though Table 310.16 lists it at 25 A in the 75 °C column. Only the specific applications that 240.4(E) and 240.4(G) allow, such as tap conductors and motor circuits, may go higher.
What size breaker goes with 14 AWG and 10 AWG wire?
Under NEC 2023 section 240.4(D), 14 AWG copper is limited to 15 A and 10 AWG copper to 30 A. For aluminum and copper-clad aluminum, 12 AWG is limited to 15 A and 10 AWG to 25 A.
Can a 20 A breaker on 12 AWG wire carry a 20 A continuous load?
No. NEC 2023 section 210.20(A) requires a branch-circuit breaker rated at least 125% of the continuous load (one expected to run 3 hours or more), so a standard 20 A breaker on 12 AWG copper serves at most 16 A of continuous load. The exception is an assembly listed for operation at 100% of its rating.
Is 12 AWG NM cable (Romex) also limited to a 20 A breaker?
Yes. The 20 A limit in NEC 2023 section 240.4(D)(5) applies to 12 AWG copper in any wiring method. NM cable is also held to the 60 °C ampacity column by section 334.80, which is 20 A for 12 AWG copper; its 90 °C rating may be used as the starting point for derating, but the result can't exceed that 60 °C value.